master:192.168.101.134

node:192.168.101.135

1.关闭服务器防火墙

systemctl stop firewalld

systemctl disable firewalld

2.在master安装Kubernetes Master

yum -y install etcd kubernetes-master flannel 

安装完成后在master机器上修改相应的配置文件

vi /etc/etcd/etcd.conf

ETCD_DATA_DIR="/var/lib/etcd/default.etcd"

ETCD_LISTEN_CLIENT_URLS="http://0.0.0.0:2379"

ETCD_ADVERTISE_CLIENT_URLS/etc/kubernetes/apiserver="http://192.168.101.134:2379"

vi /etc/kubernetes/apiserver

###
# kubernetes system config
#
# The following values are used to configure the kube-apiserver
#
# The address on the local server to listen to.
KUBE_API_ADDRESS="--insecure-bind-address=0.0.0.0"
# The port on the local server to listen on.
KUBE_API_PORT="--port=8080"
KUBE_MASTER="--master=http://192.168.101.134:8080"
# Port minions listen on
# KUBELET_PORT="--kubelet-port=10250"
# Comma separated list of nodes in the etcd cluster
KUBE_ETCD_SERVERS="--etcd-servers=http://127.0.0.1:2379"
# Address range to use for services
KUBE_SERVICE_ADDRESSES="--service-cluster-ip-range=10.254.0.0/16"
# default admission control policies
KUBE_ADMISSION_CONTROL="--admission-control=NamespaceLifecycle,NamespaceExists,LimitRanger,SecurityContextDeny,ServiceAccount,ResourceQuota"
# Add your own!

KUBE_API_ARGS=""

添加启动脚本start_kubernetes.sh

for SERVICES in etcd kube-apiserver kube-controller-manager kube-scheduler; do 
            systemctl restart $SERVICES;
            systemctl enable $SERVICES;
            systemctl status $SERVICES ;
done

在etcd中定义flannel网络

etcdctl mk /atomic.io/network/config '{"Network":"172.17.0.0/16"}'

3.在node服务器上安装:

yum -y install flannel kubernetes-node

安装完成后修改相应配置文件

vi /etc/sysconfig/flanneld 为flannel网络指定etcd服

# Flanneld configuration options  
# etcd url location.  Point this to the server where etcd runs
FLANNEL_ETCD_ENDPOINTS="http://192.168.101.134:2379"
# etcd config key.  This is the configuration key that flannel queries
# For address range assignment
FLANNEL_ETCD_PREFIX="/atomic.io/network"
# Any additional options that you want to pass

#FLANNEL_OPTIONS=""

vi  /etc/kubernetes/config

###
# kubernetes system config
#
# The following values are used to configure various aspects of all
# kubernetes services, including
#
#   kube-apiserver.service
#   kube-controller-manager.service
#   kube-scheduler.service
#   kubelet.service
#   kube-proxy.service
# logging to stderr means we get it in the systemd journal
KUBE_LOGTOSTDERR="--logtostderr=true"
# journal message level, 0 is debug
KUBE_LOG_LEVEL="--v=0"
# Should this cluster be allowed to run privileged docker containers
KUBE_ALLOW_PRIV="--allow-privileged=false"
# How the controller-manager, scheduler, and proxy find the apiserver

KUBE_MASTER="--master=http://192.168.101.134:8080"   修改master上ip

vi  /etc/kubernetes/kubelet

###
# kubernetes kubelet (minion) config
# The address for the info server to serve on (set to 0.0.0.0 or "" for all interfaces)
KUBELET_ADDRESS="--address=0.0.0.0"
# The port for the info server to serve on
# KUBELET_PORT="--port=10250"
# You may leave this blank to use the actual hostname
KUBELET_HOSTNAME="--hostname-override=192.168.101.135"修改为nodeip
# location of the api-server
KUBELET_API_SERVER="--api-servers=http://192.168.101.134:8080" 修改为master上的ip
# pod infrastructure container
KUBELET_POD_INFRA_CONTAINER="--pod-infra-container-image=registry.access.redhat.com/rhel7/pod-infrastructure:latest"
# Add your own!

KUBELET_ARGS=""

添加启动脚本startnode.sh

for SERVICES in kube-proxy kubelet docker flanneld; do 
    systemctl restart $SERVICES
    systemctl enable $SERVICES
    systemctl status $SERVICES 
done

踩的坑在node节点上安装启动总是报了如下错:

SELinux is not supported with the overlay2 graph driver on this kernel. Either boot into a newer kernel or disable selinux in docker (--selinux-enabled=false)  

解决方法

根据高亮的错误日志得知,此linux的内核中的SELinux不支持 overlay2 graph driver ,解决方法有两个,要么启动一个新内核,要么就在docker里禁用selinux,--selinux-enabled=false

重新编辑docker配置文件:
# vim /etc/sysconfig/docker 添加如下内容:

# /etc/sysconfig/docker

# Modify these options if you want to change the way the docker daemon runs
OPTIONS='--selinux-enabled=false --log-driver=journald --signature-verification=false'
if [ -z "${DOCKER_CERT_PATH}" ]; then
    DOCKER_CERT_PATH=/etc/docker
fi

~~EOF~~



Logo

K8S/Kubernetes社区为您提供最前沿的新闻资讯和知识内容

更多推荐