海思hi3519a I2C报错hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611
1.前言这周准备移植nvp6324到hi3519a板子上,可是在加载驱动时候i2c通讯不成功,移植报错hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611问题。之前一直怀疑i2c时序不对,用示波器也没有量出来问题,中间还折腾用gpio模拟i2c,均失败。可是用海思自带工具i2c_read 可以读取寄存器的值,并且是正确的。2.问题海思打...
·
1.前言
这周准备移植nvp6324到hi3519a板子上,可是在加载驱动时候i2c通讯不成功,移植报错hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611问题。之前一直怀疑i2c时序不对,用示波器也没有量出来问题,中间还折腾用gpio模拟i2c,均失败。可是用海思自带工具i2c_read 可以读取寄存器的值,并且是正确的。
2.问题
海思打印如下:
/home # insmod jaguar1.ko
[DRV] I2C Client Init
addr =30
Device ID Error... ff, Chip Count:[0]
hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611
hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611
hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611
hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611
Device ID Error... ff, Chip Count:[1]
hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611
hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611
hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611
hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611
Device ID Error... ff, Chip Count:[2]
hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611
hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611
hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611
hibvt-i2c 4562000.i2c: wait idle abort!, RIS: 0x611
Device ID Error... ff, Chip Count:[3]
Chip Count = 0
Address [0xff][0xff][0xff][0xff]
Chip Id [0xff][0xff][0xff][0xff]
Rev Id [0xff][0xff][0xff][0xff]
hibvt-i2c 4562000.i2c: wait i
3.解决方案
主要提供几个思考方向:
- 设备地址是否正确(8bit地址和7bit地址区分);
- 内核驱动是否加载;
- 复位管脚是否复位后使能;
我的设备就是把复位当作高电平有效,实际是低电平。这样初始化时候芯片复位管脚一直为低,nvp6324处于复位状态,所以通讯不成功。同时也要注意海思GPIO电压是1.8V,而NVP6324的IO管脚是3.3V,上拉电压也不能错。
更多推荐
已为社区贡献1条内容
所有评论(0)